Hobart LX30 ML-104352 Manuale Utente

NSTRUCTIONSILX SERIES DISHWASHERLX SERIES DISHWASHERSMODELSLX18 ML-104349LX18C ML-104350LX18H ML-104351LX30 ML-104352LX30C ML-104353LX30H ML-104354LX4

– 10 –INSTALLATION DIAGRAM (LX30, LX30C & LX30H) — 329301

– 11 –INSTALLATION DIAGRAM (LX40C & LX40H) — 329302

– 12 –OPERATIONCAUTION: Items such as pewter, aluminum, and silver will be attacked by sodium hypochlorite(bleach). Therefore, chemical sanitizing d

– 13 –Operating Models LX18, LX18C, LX18H, LX30, LX30C, and LX30H Dishwashers DO THIS DISPLAY SHOWS REMARKSPress ON.

– 14 –DIAGNOSTIC MESSAGESIn the event of a problem with a temperature probe, the display will flash "P1," "P2," or "P3"

– 15 –MODELS LX30, LX30C and LX30HWASH/RINSE CYCLE TIMESWash 85 Sec.**Drain* 10 Sec. Max.Dwell 4 Sec.Rinse 10 Sec.Dwell 6 Sec.* Drains off about 1 ga

– 16 –CONTROLS — Models LX40H & LX40C (Fig. 4)Fig. 4Operating Models LX40H & LX40C DO THIS DISPLAY SHOWS REM

– 17 –Operating Models LX40H & LX40C (Continued) DO THIS DISPLAY SHOWS REMARKSOpen door; slide rack of READY.dish

– 18 –DIAGNOSTIC MESSAGESIn the event of a problem with a temperature probe, the display will flash PROBE and CALL SERVICEwill be lit. The respectiv

– 19 –MANAGER PROGRAMMING (Machine Must Be In READY Mode)To enter the Manager Programming Mode, you must first enter the Operator Programming Mode byp

– 2 –© HOBART CORPORATION, 1993TABLE OF CONTENTSGENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 20 –PROGRAMMABLE VARIABLES AND RECOMMENDED SETTINGS — MODELS LX40H & LX40CThe following functions of the dishwasher are programmable. The chart

– 21 –Dishes must be scraped and/or rinsed to remove food particles and other debris. Never use steel woolon ware to be loaded into the dishwasher.

– 22 –3. With a damp cloth, wipe the interior of the machine, the water level probes (Fig. 9), and the waterlevel probe under the fine strainer. DO N

– 23 –MAINTENANCEDELIMING — GENERALWARNING: DELIMING SOLUTION, RINSE AGENTS, OR ANY OTHER KIND OF ACID MUST NOTCOME IN CONTACT WITH BLEACH OR RINSE S

– 24 –DELIMING — Models LX30, LX30C & LX30H 1. Remove standpipe assemblies from chemical containers and place them as close to the floor aspossib

– 25 –DELIMING — Models LX40H and LX40CModels LX40H and LX40C are equipped with an automatic delime cycle reminder. After thepreprogrammed number of

– 26 –TROUBLESHOOTINGThis section outlines various symptoms and possible causes that may be encountered in the event ofabnormal machine operation. If

– 27 – SYMPTOM POSSIBLE CAUSESUnexpected results on 1. Etching — usually caused by any combination of hi

– 28 – SYMPTOM POSSIBLE CAUSESMachine fills too high or 1. Machine not level — see LEVELING in this manual.leaks from door.

– 3 –Model LX30 DishwasherInstallation, Operation, and Care ofLX SERIES DISHWASHERSSAVE THESE INSTRUCTIONSGENERALThe LX Series dishwashers are fully a

– 4 –INSTALLATIONUNPACKINGImmediately after unpacking the dishwasher, check for possible shipping damage. If this machine isfound to be damaged, save

– 5 –PLUMBING CONNECTIONSWARNING: PLUMBING CONNECTIONS MUST COMPLY WITH APPLICABLE SANITARY, SAFETY,AND PLUMBING CODES.DrainA drain hose is provided

– 6 –ELECTRICAL CONNECTIONWARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THEAPPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/O

– 7 –Refer to the data plate on the front of the machine and the label inside the control drawer at the powerconnection for proper selection.Use stran

– 8 –DETERGENT AND RINSE AIDIf manually adding detergent in an LX18, LX18C, or LX18H at the beginning of each cycle, the machinemust be programmed to

– 9 –INSTALLATION DIAGRAM (LX18, LX18C & LX18H) — 329300